A-Train Exp.+ MANUAL

[Run Bus and Truck (Rail / Station / Train)]	TOP PAGE

≪Manage Buses and Trucks

Schedule Settings of Junction And Traffic Light≫

Schedule Settings of Bus Stop and Depot

Hover the cursor over a bus stop or a depot. Press △ button or left-click to show the menu of schedule settings.
You can switch Information (information of a bus stop or a depot) and Schedule (menu for schedule settings).

Schedule of Bus Stop and Depots

【Select Bus and Truck】
Press × button and directional buttons / left click to select a vehicle to set its schedule.

[Copy]: Temporarily copy a schedule of a selected vehicle. Copied vehicle's No. is framed.
[Clear copy]: Click "Copy Clear" button to delete a copied schedule.
[Paste]: Apply a copied vehicle's schedule to a selected vehicle.
[Apply to All Bus & Truck]: Apply a selected vehicle's schedule to all vehicles.

【Action Mode】
Set conditions for an arrived vehicle to depart a bus stop or a depot.

[Stop]: Adjust the slider to set time length to stop a vehicle at a bus stop or a depot.
[Dep.Time]: Adjust the slider to set a departure time of a vehicle, and an interval between the next departure time.
[Pass]: Pass a bus stop or a depot without stopping.
[Separate Shcedule]: Available to set multiple departure times.

Note: Sufficient length of time is necessary for loading and unloading materials of a truck. Shorter stoppage time causes unfinished loading and unloading.

【Direction】Note: Available only for Bus Terminal and Depot (Large).
Set a direction to depart of a vehicle arriving at a bus terminal or a distribution center.

[Straight]: depart to the opposite direction on arrival at a bus terminal or a distribution center.
[Reverse]: keep a direction on arrival at a bus terminal or a distribution center to depart.

【Service Schedule】Note: Available if advanced setting is enabled.

Set months and days of operation.
[Yearly]: Operational throughout a year.
[SPG]: Operational from March to May.
[SUM]: Operational from June to August.
[FALL]: Operational from September to November.
[WIN]: Operational from December to February.
[OFF]: Out of operation throughout a year.
[1]~[12]: Operational in selected month(s).

[Daily]: Daily service
[Week Days]: Weekday service
[Holidays]: Holiday service
[Sun]~[Sat]: Operational on selected day(s).

Adjust Slider to Set Time

【Stop】
By setting a stoppage time, you can stop a vehicle at a facility for a certain time.
Hover the cursor over a departure time to set a stoppage time. Then press L1 button or R1 button / left-click / use the mouse wheel to adjust.

【Departure Time】
By setting departure times, you can also set ① departure time of the first vehicle, ② interval between the next vehicle, and ③ departure time of the last vehicle.
Hover the cursor over a departure time to set. > Press L1 button or R1 button / left-click / use the mouse wheel to adjust. If departure time of the last vehicle is before that of the first vehicle, the last vehicle will depart after midnight.

【Separate Shcedule】 For manual setting of multiple departure times and directions to depart, follow the process below. The maximum number of departure time for each vehicle is 1000 (total number of branching point). No additional schedule more than 1000 is available.

① Hover the cursor over a departure time to set. > Press L1 button or R1 button / left-click / use the mouse wheel to adjust.
　The spots set are displayed with white lines.

② The number of current scheduled time.

③ Go to the previous (next) number of scheduled time.

④ Set how to treat passengers or freights on arrivals.
　By clicking the button, switch loading and unloading, loading only, unloading only, or no loading and unloading.
　Note: Available if "Set Passenger & Load Service" of the Schedule settings in the Option menu is turned on.

⑤ Adjust Separate Schedule Bar to the current time.

⑥ Register the time being displayed on the Separate Schedule Bar.

⑦ Delete the current number of schedule time.

⑧ Delete all numbers of scheduled times.

Set Departure Time for Usual and Special Schedule

【Special Train Schedule】Note: Available if advanced setting is enabled.

Select [Schedule] > [Schedule 2].
Enable a special schedule by changing the status of [Extra Service Schedule] from [Suspend Service].

Once a special schedule is enabled, a red icon will appear on the [Schedule 2] button.Special schedules take priorities over usual schedules.
Note: Usual schedules become out of operation if special schedules are [Every Month] and [Daily].

Advanced Settings of Bus Stop and Depot

For detailed schedule settings of bus stops and depots, open the [Option] menu, select [Schedule] and turn on the following functions.
Note: Other settings do not affect schedule settings of bus stops and depots.

【Set Passenger & Load Service】
Turn on to show the settings of [Passengers] and [Materials] and set how to treat passengers and materials on arrivals at a facility. Turn off to set all [Getting On & Off] / [Load & Unload] as　motions at a facility.

【Set Service Schedule】
Turn on to show [Service Schedule] and [Extra Service Schedule]. > Set a date to apply schedules of a bus stop or a depot. (Note: Schedules are out of operation except specified dates.)
When turned off, and if setting of stoppage time of a facility is 5 minutes, all vehicles will stop at the facility for 5 minutes everyday.

【Minimize Units of Time for Schedule】
Turn on to set 1 minute as the minimum unit of time for schedule of a bus stop or a depot. > Press L1 button or R1 button / Use scroll wheel to adjust schedules.
Turn off to set 5 minute as the minimum unit of time.